What if you notice that your Jeep Patriot tail light isn’t working properly? Before you get back on the road, you’ll have to fix or replace it, right? Failure to do so puts you and other drivers in danger.
The taillights should be inspected and replaced as needed regularly. Taillights are designed to communicate what you’re doing to others. The taillights tell traffic behind you whether you’re turning, preparing to stop, stopping, or backing up.
In this article, I’ll go through how to replace the tail light bulbs on a Jeep Patriot.
Key Points:
- It’s essential to have your taillights inspected and replaced on a regular basis because they signal to drivers behind you that you’re turning, stopping, or backing up.
- Replacing your tail lights is a great method to improve the appearance, security, and pass vehicle inspections on your Jeep Patriot.
Causes Behind a Tail Light to Stop Working?
There could be several reasons why your Jeep Patriot’s tail light isn’t working. Some are given below-
1. Defective Fuse
Your car’s fuse box is most likely under the hood or on the front passenger side of the cabin. Electrical components throughout your vehicle are controlled by fuses.
Whether your tail light has stopped working, check the fuse box to see if it is the source of the problem. Your car’s owner’s manual details the location of your fuse box and the placement of your tail light fuse.
To check if your tail light fuse is working, use a fuse tester. If the fuse does not light up, get a new one with the same amperage and install it.
2. Bulb Burns Out
Long-term use of a tail light bulb might cause it to burn out. Remove the tail light cover and inspect the bulb to see whether this is the case.
You can inspect the filament of the tail light bulb to see whether it’s broken. If the filament is broken, the bulb must be replaced.
3. Socket No Longer Works
A tail light bulb socket may fail at some point. Moisture entering the socket and producing corrosion can cause this. It can also happen as a result of a faulty wire connection between the socket and the bulb.
Look for any discoloration or damage when evaluating a socket. The socket should be changed if it is blue, brown, or white, or if the pins are bent or damaged.
The proper way to inspect the taillights
Checking your taillights is a straightforward procedure. It should just take you a few minutes to do the inspection. What you’ll need to do is complete the following steps:
- You’ll be checking the brake lights, turn signals, and running lights.
- You might wish to get the help of someone to examine the taillights.
- If you need to check the lights on your own, back up to a window and look through the reflection in your back window.
- Apply the brakes.
- Turn on your right turn signal first, then your left turn signal.
- Set the lights to run at night.
- Make sure your danger lights are turned on.
Why Do You Need to Repair a Broken Tail Light Right Away?
It is better to fix or replace a broken tail light from the mechanic. The longer you delay dealing with this problem, the more likely an accident may occur.
When it comes to car repairs and maintenance, be proactive. Regularly inspect your taillights; fix them right away if any flaws are discovered.
Tail Light Bulbs Replacement Guide:
It’s important to ensure your Jeep Patriot’s condition and ensure that it functions properly. Even anything as simple as a tail light falls into this category.
If one or both of these lights are out when night falls or bad weather strikes, other drivers will have a difficult time seeing your Jeep Patriot. It’s vital to replace tail light bulbs, but it doesn’t have to be complicated.
Step-1: Disconnect the Battery
- Working with bulbs and cables necessitates extreme caution. Begin by removing the battery from your Jeep Patriot. Shock or electrocution will be reduced as a result.
- After that, open the trunk or back hatch to get to the taillights. You can do this in a well-lit area or with a flashlight. The entrance point could be obstructed by extra carpeting or padding.
- Remove them until the back of the taillights can be seen clearly. You’ll need a screwdriver for some autos because they have a panel that needs to be removed.
Step-2: Remove The Bulb Holders
- Remove the bulb holders from the backside of the lamp once you can see and touch the taillights. This can be accomplished by simply rotating them clockwise.
- Remove any broken or burned-out bulbs; if the bulbs are broken, be careful not to cut yourself.
- Replace the bulbs with the new ones while wearing gloves. The gloves will aid in keeping the bulbs clean, extending their life and increasing their efficiency.
Step-3: Remove The Assembly
- Your work isn’t finished yet. The tail light assembly must then be removed. This shouldn’t be a problem once you’ve located and removed the nuts.
- To help remove the nuts, you may need to use some grease or oil. At this stage, the assembly should easily slip out.
Step-4: Final Processes
- When you’re ready to reinstall the component in the housing, tighten the bolts by hand first before using a ratchet. It’s important not to overtighten these since they can cause the housing to crack or break.
- Replace the bulb holders with new ones. These should have a different appearance than the turn signal and brake lights.
- Replace the carpet and any panels in the trunk to complete the job.
- Remember to reconnect the vehicle’s battery.
Advantages of Replacing Tail Light Bulbs
Replacing the tail lights on your Jeep Patriot is probably more advantageous than you think. Replacing your tail lights is an excellent way to improve the appearance of your Jeep Patriot, with the following advantages:
- Enhancement of appearance
- Enhanced security
- Aids in the passing of vehicle inspections
- Protect yourself from additional damage
Is there a difference in headlights and taillights?
Yes, there is a significant distinction between the two. They differ not just in terms of use, but also terms of bulb form, size, and function.
Is it possible to utilize headlight bulbs as taillights?
LED bulbs can be utilized as brake lights and, given their advantages, should be the preferred option. LED taillights are brighter, faster to illuminate, and last longer than halogen taillights, making them a better choice.
What Are the Benefits of LED Tail Lights?
LED taillights are brighter, faster to illuminate, and last longer than halogen taillights, making them a better choice.
LED taillights are safer and more cost-efficient than traditional tail lights because they react faster, last longer, and use less power. They also handle moisture, humidity, and shock better, making them safer and more cost-effective.
Final Words
Tracking down the source of a broken tail light can be difficult and frustrating. If you’re not sure what’s causing your car’s defective tail light, it’s good to take it to a professional repair. That way, you can get your tail light inspected, figure out what’s wrong, and get it serviced or replaced.
Related Posts: