No matter how pretty they look, the dash lights can get your heartbeat racing even if any one of them comes on. So, it’s understandable if you get a goosebumps-like sensation when you see all the warning lights on your Jeep Wrangler come on! Your first and foremost priority is contacting your local dealership or the nearest mechanic.
When all your dash lights turn on simultaneously, there may be an issue with the charging system or your Wrangler’s alternator. If that’s the case, you should avoid driving long distances as your Jeep may lose power at any moment.
Each of the warning lights indicates a different problem. While that may sound very worrying, you can fix this with some know-how about why Jeep Wrangler is all warning lights on. So, let’s get cracking.
Why Is Jeep Wrangler All Warning Lights On?
If you see multiple lights are on, chances are, more than one system is in disarray. But if you see that all the lights are turned on, there’s likely something wrong with your alternator.
The sooner you take care of this problem, the better you can minimize the damage.
Let’s take the Jeep Wrangler JK, for example. Here are a few common reasons why the warning lights might be on,
- Damaged wire in wheel sensor
- Clock spring error
- Fault Codes on TCCM
- Blockage on ACC Sensor
- Dust damage in airbag sensors
5 Solutions for Jeep Wrangler All Warning Lights On:
There can be an entire myriad of problems that can make the warning lights go off. But there’s no need to worry. All of these problems are fixable.
However, the quicker you take the necessary steps, the easier it will be to fix the problem.
1. Damaged Wire In Wheel Sensor: Fix ABS Light
ABS stands for the anti-braking system. So if there’s something wrong with your AB system, the warning light will go off.
In most cases, the light flashes due to a damaged wire in the wheel sensor. You can usually tell if there’s any malfunction by checking if a wire is rubbing anywhere.
The anti-braking system prevents the wheel from locking up. That way, the driver can safely steer the car without worrying about losing traction in the middle of the road.
The system isn’t functioning correctly if the ABS warning light comes on.
Check to see if the wires are well-organized. If the cables are in order, check if your brake fluids are leaking. If the brake fluid is leaking, get it fixed to bring back the full functionality of your Jeep Wrangler JK.
And if you have to replace the control module, the parts should cost you around $420; generally, the labor costs are approximately between $120 and $160.
2. Clock Spring Error: Replace Electronic Stability Control Light
If you see the ESC light is on while you’re not in 4L, there might be a problem with your clock spring.
However, it’s not mandatory that you need to park the car immediately unless you feel like the malfunction is causing the braking system to go on and off on its own.
This may be because you hit an obstacle and bent your front end out of alignment. It could also be because you have a bad clock spring.
The Electronic Stability Control or the ESC light indicates if the system is turned off. If you see the light go on, don’t panic.
If the braking system is functioning normally, you can drive your Jeep home, or if you prefer, to the nearest garage. However, the braking system keeps going on independently, which can be problematic.
First, check if the tire pressure is stable and symmetric all around. There shouldn’t be a difference of more than 2-3 psi between the tires.
Next, take a look at the steering wheel. Make sure that the steering wheel remains straight when the Jeep is straight. And if needed, adjust the drag link.
But even if the light doesn’t go away, you may need to replace the clock-spring sensor. That should cost you about $230.
And if you aren’t confident about doing the inspection, you can ask your local mechanic for help. Depending on your area, you’ll have to pay the expert approximately a hundred bucks.
3. Fault Codes on TCCM: Diagnose and Repair 4WD Warning Light
The four-wheel drive is one of the essential features of the Jeep Wrangler. So, it’s only natural that you’ll want to keep it functional.
Make sure to keep your eye on the SERV 4WD warning light. If you see the warning light come on while you’re driving, the 4WD system isn’t working well.
Unless you have a scan tool, contact the dealership. But if you have the necessary tools, you can troubleshoot the problem yourself.
Check the transfer case control module or TCCM for the fault codes. You can read it with a scan tool. Then, correctly diagnose the problem according to the fault code and repair it. After that, everything should be back to normal.
If you don’t have a scan tool, you need to get an expert’s help. It can be pretty expensive. Generally, the dealerships will charge you around $700 for this service.
4. Blockage on ACC Sensor: Clean Service Adaptive Cruise Control Light
The Adaptive Cruise Control System helps maintain a preset distance between your Jeep and the vehicle in front. It’s a safety feature that notices when the car in front of you starts slowing down to prevent any accidents.
If the ACC light on your dashboard comes on, your Cruise Control system is malfunctioning. In that case, you should consider turning your engine off and getting the ACC unit looked at.
One common cause that can turn the ACC warning light on is if there’s any debris stuck on the sensors. Check to see if that’s the case and if it is, you can easily clean the trash up, and your ACC should be fully functional again.
On the other hand, if you don’t want to get your hands dirty, the inspection costs should be around a hundred dollars. So with that, you should be good.
5. Dust Damage In Airbag Sensors: Get Expert Help About Air Bag Warning Light
If you see the airbag light repeatedly blinking, there may be an issue with the clock-spring sensor. The most likely scenario would be that dust has damaged the sensor, and that’s why the airbag light is flashing.
On the other hand, if the airbag light remains on, that can be a severe problem. This indicates that the airbags won’t deploy even when you need them.
So, if you see the light is staying turned on, don’t take the Jeep out before fixing the problem.
As its name suggests, the airbag light indicates something wrong with your Jeep’s airbags. It can probably be due to the dust messing up the clock-spring sensor in your steering wheel.
Whatever the reason, if you see the light flash or remain on, it’s best to exit the vehicle and get your Jeep towed to the dealership.
While diagnosing and repairing the problem is possible, it’s highly recommended that you ask the expert’s opinion on this one since it’s a significant safety issue.
So, make sure you have a little over 270 bucks in your wallet. The parts cost around $170, and the service charge varies between $90 and $100.
Frequently Asked Questions (FAQs)
While we tried to cover most of the common problems you may have with your Jeep Wrangler, it’s understandable that you may have some other questions. That’s why we have answered some of the most frequently asked questions regarding the Jeep Wrangler.
Can I reset my Jeep’s warning lights?
It’s a five-step process that’s easy to execute.
- Turn off your engine and take the key out of your ignition
- Detach the battery terminals
- Wait for around five minutes
- Reattach the battery terminals
- Insert the key into the ignition and turn it to the run position without starting
And your warning should have reset.
What does the car with the squiggly lines mean?
This symbol refers to the vehicle stability assist program. If the light is flashing, that means the assistance program is functional.
However, if you notice that the sign has OFF written just below it, the vehicle stability assist system is off.
Can I drive with the traction control light on?
If you see only the traction control light, you should be able to drive your Jeep.
However, your whole braking system is compromised if you see that the ABS warning light, the traction control warning light, and the red brake-warning light are on. In that case, getting your vehicle looked at is better.
What can cause the traction control light to come on?
The traction light sensor can be affected by debris. Another reason can be that there’s a problem with the connections between the ECU and the sensors.
Conclusion
The warning lights are there to notify you of any imminent problems. So, you should know what each of those lights means and what you need to do when they come on.
Simply put, a blinking ESC light and a solid engine light mean you’re in the clear. But a blinking engine light and a solid ESC light usually mean trouble.
But now that you know why your Jeep Wrangler has all the warning lights on, you shouldn’t have any more problems. Drive safe!
Related Posts: